PCPartPicker

  • Log In
  • Register

Comments

Gioffry's Completed Build: Gioffry gaming PC

FurryJackman 3 Builds 1 point 5 months ago

Bottom and side intakes, then it uses natural heat radiation to have heat rise out of the case.

Cheg's Completed Build: The Compensator!

FurryJackman 3 Builds 2 points 5 months ago

Good homage to Bitwit's Dancase build, also with an AIO.

Also, cat for scale +1!

pacho014's Completed Build: PMS Ryzen 5 2600x w/ GeForce GTX 1050 Ti

FurryJackman 3 Builds 3 points 5 months ago

Make sure your FFmpeg has NVENC support for the hardware accelerated transcoding in Plex.

Otherwise, Yay Linux!

jdavid.net's Completed Build: AMD Threadripper 2 2950x - 2x SLI 2080 TI FE - Fractal Design Define C SFF Mid ATX ( Fall 2018 )

FurryJackman 3 Builds 3 points 5 months ago

No, that's Steve from Gamers Nexus.

https://i.redd.it/57i0ure1rxi11.png

Crazybaby's Completed Build: A red/black build MSI

FurryJackman 3 Builds 6 points 5 months ago

Right now, this fan config has no intakes. I recommend flipping the front fans to intake, cause right now the case is in an extreme negative pressure situation.

spydo111's Completed Build: My modest gaming build

FurryJackman 3 Builds 1 point 5 months ago

Around BCLK frequencies of 160-190Mhz, there's a chance you'll encounter a BCLK hole. This means no matter what voltage, timings, LLC you set, it will never be stable if your BCLK frequency is inbetween 160 and 190.

If you push past that to 191-200Mhz BCLK, you can more than often find stability again on P55/X58 chips.

spydo111's Completed Build: My modest gaming build

FurryJackman 3 Builds 1 point 5 months ago

Watch out for BCLK holes around 160-190Mhz. I had that experience on P55. If you can get it all the way to 200x20 it might be better if your clockgen can handle it.

fourdoor's Completed Build: Tha Rippa

FurryJackman 3 Builds 2 points 5 months ago

That Duke is just waiting for a waterblock.

Excellent start with a monoblock to an open loop!

jl0021hk's Completed Build: X58 Reborn

FurryJackman 3 Builds 1 point 5 months ago

Good novelty build! And in a Define Mini C to boot!

Lotstodo's Completed Build: 4K HTPC - Evolv Shift & 2080 Ti

FurryJackman 3 Builds 2 points 5 months ago

I see you replaced the Realtek WiFi card with an Intel one. No unforseen incompatibilities?

The M22 is suited for the i5, where as the EVGA CLC 120 would be suited for the 8700K. If you did feel the need to upgrade 120mm coolers, the EVGA CLC 120 works well inside a Shift.

MORPHEUS1986's Completed Build: Odin the Threadrippa

FurryJackman 3 Builds 2 points 5 months ago

Just to update:

Apparently the GC-Titan Ridge Thunderbolt 3 card does not require the Thunderbolt header to work on X399:

https://egpu.io/forums/builds/thunderbolt-3-on-amd-x399-threadripper-rtx-208032gbps-tb3-razer-core-x-win10-1803-theitsage/

r33cwn's Completed Build: 1080p Overkill

FurryJackman 3 Builds 1 point 5 months ago

You could swap to a Cryorig M9a which would allow you to rotate the cooler. Seems some be quiet AM4 mounts just have this flaw.

Stemor61's Completed Build: Cheap, average user build

FurryJackman 3 Builds 1 point 5 months ago

+1 for Linux. :D

uswg01's Completed Build: SETI Test Bench

FurryJackman 3 Builds 1 point 5 months ago

Sorry you've been getting such hostile comments.

In that small space, a SFX power supply that's fully modular will help with cable management, since the EVGA one you currently have is not modular. All you will need is a SFX to ATX PSU mount adapter.

I'd recommend a Corsair SF600 for this.

Lurick's Completed Build: Goliath v3.0 - Final

FurryJackman 3 Builds 1 point 5 months ago

Very faithful homage to Skunkworks. Jay would be proud. :)

vinhgg's Completed Build: Clean Black & White PC (Noctua Forever <3)

FurryJackman 3 Builds 0 points 5 months ago

Very surprising how the Palit card fits so well with the Chromax Noctua cooler!

n1ghthawk9's Completed Build: Ryzen 7 mITX Gaming Rig

FurryJackman 3 Builds 1 point 5 months ago

That tidbit about the WS2812b chip might be useful for people trying to run ARGB on Linux.

This project could use some of that insight:

https://gitlab.com/CalcProgrammer1/KeyboardVisualizer

Thumbless's Completed Build: Rainbow Bright

FurryJackman 3 Builds 1 point 5 months ago

Rear fan might benefit from being an exhaust. The GPU would be able to vent hot air out in that case.

For your top exhausts, run the rightmost one near the AIO slower than the rest of the fans, and the leftmost one faster. This promotes airflow towards that section of the case.

pilijong's Completed Build: RED?

FurryJackman 3 Builds 2 points 5 months ago

Uh, those don't have as good VRMs as the Tomahawk. In fact, Buildzoid called Gigabyte out on their ~$100 offerings.

Get the B450 Tomahawk. You won't regret it.

pilijong's Completed Build: RED?

FurryJackman 3 Builds 1 point 5 months ago

Sub $100 boards on AM4 I guarantee you don't overclock well.

pilijong's Completed Build: RED?

FurryJackman 3 Builds 1 point 5 months ago

B450, cause it has really good components, and would unlock XFR2.

guitpicker007's Completed Build: Atta Boy

FurryJackman 3 Builds 2 points 5 months ago

There is no excuse for a poor quality PSU. 80+ Bronze or bust.

loliceforce's Completed Build: Ayymd lmao

FurryJackman 3 Builds 4 points 5 months ago

Better than the Verge build.

You almost fooled us with the memory, but you know better than the Verge.

pilijong's Completed Build: RED?

FurryJackman 3 Builds 1 point 5 months ago

Yeah, for better OCs, you could get the MSI Tomahawk which would outperform this Gigabyte one OC-wise.

Pandemicman's Completed Build: Scratching that Upgrade Itch

FurryJackman 3 Builds 3 points 5 months ago

It is a shame the OLED on the pump only changes images when the software is loaded and not all the time. Revision 2 should just have a internal memory fallback to do the animations.

LackingPotatoes's Completed Build: Modest Ryzen Build

FurryJackman 3 Builds 2 points 5 months ago

Oh yeah, that's right, they only just started on the X399 Creation.

Yeah, then don't do PBO on this board.

LackingPotatoes's Completed Build: Modest Ryzen Build

FurryJackman 3 Builds 1 point 5 months ago

If you're doing PBO, you can do a negative voltage offset and still remain stable.

mongrel_stu's Completed Build: Ripper

FurryJackman 3 Builds 2 points 5 months ago

Have you checked if your board supports ECC? Ryzen on supported motherboards can support ECC memory.

timatn's Completed Build: AMD Ryzen 7 Mobile Workstation

FurryJackman 3 Builds 1 point 5 months ago

Where did you get the Noctua L9a-AM4? That's hard to find where I am.

deequ's Completed Build: Ryzen Trooper

FurryJackman 3 Builds 1 point 5 months ago

Good choice of components. Since you run no mechanical hard drives, you can move the decorative panel on the R6 back to make the case feel more roomy when you look into it from the tempered glass side.

setibox's Completed Build: Chibineko

FurryJackman 3 Builds 3 points 5 months ago

Very good idea to slap a UPS on it due to brownouts in your area. Don't want any of these components to be killed by bad power.

Dougie4242's Completed Build: Ti-Ripper

FurryJackman 3 Builds 1 point 5 months ago

Since I posted that 4 months ago, it was revealed 1st gen Enermax TR4 AIOs had a manufacturing defect due to corrosion.

If you were still considering the Enermax AIO, get the 2nd gen model. (it will have Addressable RGB as the main difference)

Porphi's Completed Build: NCase M1 w/ RTX 2080

FurryJackman 3 Builds 1 point 6 months ago

Damn, sorry to hear about the Vardars shattering.

The Fractal Design HP-12 and HP-14 are good choices as well.

fallenpixel's Completed Build: Mid-range Ryzen PC for School

FurryJackman 3 Builds 1 point 6 months ago

Don't use the Experimental branch right now as that's experimenting with asset compression which is causing all kinds of havok on OpenGL systems.

fallenpixel's Completed Build: Mid-range Ryzen PC for School

FurryJackman 3 Builds 1 point 6 months ago

Have you tested Steam Play/Proton on the RX 580 yet?

PCPartPicker Blog Post "NVIDIA GeForce RTX 2080 Ti Benchmarks"

FurryJackman 3 Builds 1 point 6 months ago

Can you test Dota 2 using Vulkan? Supposedly that's where Nvidia put a lot of effort into async compute.

ihateolives's Completed Build: Cougar QBX

FurryJackman 3 Builds 1 point 6 months ago

I honestly feel like a SFX power supply with a bracket will give more room to breathe inside the cramped case.

michaelkhoo's Completed Build: DreamTeam32

FurryJackman 3 Builds 2 points 6 months ago

More pictures! I want to see the X399 Creation fully populated!

csanroman's Completed Build: r7 ripp3r

FurryJackman 3 Builds 1 point 6 months ago

Dual boot! +1

But can you explain the rationale behind the case airflow?

Tyloo_wNv's Completed Build: A4-SFX + 2700x + 1080Ti FTW3

FurryJackman 3 Builds 3 points 6 months ago

Had to reply again because I wish I could +1 again for the cat.

Tyloo_wNv's Completed Build: A4-SFX + 2700x + 1080Ti FTW3

FurryJackman 3 Builds 1 point 6 months ago

Huh, so the 2700X even under PBO works great with the C7 Cu in such a cramped case!

Jasp88's Completed Build: Bucketlist: Build My Own PC [Check!]

FurryJackman 3 Builds 1 point 6 months ago

You might need a Uninterruptable Power Supply. The voltage coming from your wall might not be enough and it's tripping the AC undervoltage protection of your PSU.

ryanfisher's Completed Build: Complete Overkill (FIRST PC)

FurryJackman 3 Builds 1 point 6 months ago

Which direction are the fans blowing the air on the H75? Ideally it should be blowing into the case, because any airflow (even if it's warm air) benefits the thermal situation in the case.

GeeMac's Completed Build: Corsair 280X - My first ever build!

FurryJackman 3 Builds 1 point 6 months ago

Why is one fan intake and one fan exhaust on the AIO? Cyclonic airflow isn't great for the air patterns in the case. I recommend making both AIO fans exhaust (like the leftmost fan looking into the case) and adding slim intake fans below the GPU to promote positive pressure airflow.

Prolimatech makes good slim fans:

https://pcpartpicker.com/product/MsL7YJ/prolimatech-case-fan-ultrasleekvortex12white

Digitaltim's Completed Build: Ryzen 2600 build

FurryJackman 3 Builds 1 point 6 months ago

Yup, definitely replace a PSU when it starts buzzing loudly.

The new PSU you got also has all black cables, and would look better as the build photo IMO.

If you don't activate Windows, you can NEVER change the wallpaper, themes, or screensavers.

Watts_Up's Completed Build: Zaurak - Dan A4 VR Machine

FurryJackman 3 Builds 2 points 6 months ago

Bitwit tried a 92mm AIO. The height of your memory, if it's too high, will cause your AIO tubing to hit the side of the case, popping it out. No temperature improvement was seen.

You could see about getting a Cryorig C7 Cu, like this build:

https://pcpartpicker.com/b/qjLJ7P

wasim's Completed Build: First Custom Build - R7 2000x - GTX 1060 3GB

FurryJackman 3 Builds 1 point 6 months ago

You should try KVM/QEMU sometime. It's what unRAID bases it's paid Linux distro off of.

wasim's Completed Build: First Custom Build - R7 2000x - GTX 1060 3GB

FurryJackman 3 Builds 1 point 6 months ago

Any chance you have tried Steam Play/Proton if you're running Linux as the host OS?

sysdmp's Completed Build: Reaper v2 (Gentoo Linux threadripper workstation)

FurryJackman 3 Builds 1 point 6 months ago

You have learned well from Wendell!

Both a lstopo and a IOMMU listing in the same build description!

AC1DFOX's Completed Build: Hyrule Warrior - Zelda Themed Build

FurryJackman 3 Builds 5 points 6 months ago

The literal last thing you need is AIO sleeving:

https://cablemod.com/product/cablemod-aio-sleeving-kit-series-2-for-evga-clc-nzxt-kraken-white/

This is so clean! Perfect for Bizhawk and Ocarina of Time Randomizer!

Page
3
·
·