MicroATX Mid Tower
Side Panel Window
Front Panel USB 3.0
Motherboard Form Factor
- Micro ATX
- Mini ITX
Full-Height Expansion Slots
Half-Height Expansion Slots
Maximum Video Card Length
315 mm / 12.402"
External 5.25" Bays
Internal 3.5" Bays
- 22 points
- 36 months ago
from completed build Long Distance Lover
Cheap! Cheap! Small enough micro ATX case without too much compromise. I mean check it out, you have cable management area in the back, removable drive cage with slide rails for 2 hard drives, you can install up to 5 120mm fans with 2 in front 1 in back 2 up top, there's 5.25 slot, lots of SDD mountings and the PSU installs the right way (intake at the bottom). Only thing I will change would be to use rubber for feet and rubber hdd rails to replace the plastic ones they use that's kinda noisy.
- 19 points
- 8 months ago
from completed build Tech Service Learning Build for the Community
This is a very small case, and if you have a MicroATX motherboard then the largest cable management slots will be covered. I found it hard to route my cables and the case was oddly oriented when it came to routing my cables. But I cannot complain for how much it cost. This is a great case if you do not care about cable management.
- 18 points
- 36 months ago
from completed build ~$500 CAD Budget Gaming Build
Not a bad case at all for the price, sturdy, good-looking, decent cable management. PCIe slots once broken will stay broken, and only comes with one backup slot so you'll have holes in your pc if you put in a GPU and then remove it. The top slot is obstructed by the case so I had to plug my monitor in on the second one. Might be a problem for some people. Drive bay can be faced on both sides, comes with an nice and quiet 120mm rear turbo fan and has an air filter at the bottom where the PSU goes. Lots of space for airflow.
- 16 points
- 23 months ago
from completed build My first pc build (Ryzen 5)
The quality of this case is great, I just had many issues with cable management, as many of the holes used to route wires were covered when I installed my mATX motherboard.
- 15 points
- 30 months ago
from completed build Work Pc
Surprisingly good case for the money. The HDD cage is removable and there's quite a lot of space behind the mother board tray and below the CD ROM bay which is fully covered so you can't really see any cables. The bulges in the side panel make it easy to cram cables behind too. Obviously it's a bit flimsy but there are no sharp edges.
- 13 points
- 22 months ago
from completed build "Is it done yet?"- Build
You get what you pay for. Not a lot of room in it. One of the holes for a mobo standoff was broken and i couldnt screw one standoff in. otherwise its good for a budget build
- 12 points
- 11 months ago
from completed build The Minimum Wage PC
Basic case for not a lot of money. Definitely not flashy, but works great for what I need.
- 11 points
- 16 months ago
from completed build Big, Black and Slightly Powerful
The case is aesthetically pleasing and I didn't cut my fingers building in it. If what's on the inside matters to you then forget what I just said and note that the cable management in this case is absolutely horrifying. I somehow managed to fit the cables in correctly so that the side panel wasn't bulging out but if you just so happen to find a case with better options for cable management and is around the same price as this one, jump on it.
- 11 points
- 1 month ago
from completed build Impulse
The case is phenomenal for the price. It's nice and compact and the side panels are reversible. There are plenty of drive mounting locations in the small case along with support for 5 120mm fans. It also surprisingly has a pretty high-quality PSU filter which glides in and out. But keep in mind, it does not come with a dust filter for the top two fan mounts. So you will want to get a dust filter off of Amazon or just put your GPU box on top of it like I did. The fact that this case is only $40 is pretty insane to me considering the quality and structural integrity you get.
- 10 points
- 21 months ago
from completed build $600 CAD Budget PC (My First PC)
Really nice looking case exterior wise. However, cable management was kind of tricky as I had to remove the 20+4 pin power connector once while trying to reroute my cables, but other than that I was able to pull some clean decent cable management.
- View Compatible CPU Coolers
- View Compatible Fan Controllers
- View Compatible Motherboards
- View Compatible Optical Drives
- View Compatible Power Supplies
- View Compatible Sound Cards
- View Compatible Storage
- View Compatible Video Cards
- View Compatible Wired Network Adapters
- View Compatible Wireless Network Adapters
- Intel Pentium G4560
- GeForce GTX 1050
- Intel Core i3-6100
- GeForce GTX 1050 Ti
- AMD Ryzen 3 1200 (@3.4GHz)
- GeForce GTX 1050 Ti