Description

My last build, OmegaCore, did MS Paint like a charm. But now with SpectrumCore, I can finally use Paint 3D!

Comments

  • 20 months ago
  • 1 point

I have this same case but use a Corsair H105 which is kinda thick so I have it mounted to the front which limits my GPU length. How was the difficulty of mounting your NZXT to the top?

Also what mouse pad is that, it’s cool as hell!

  • 20 months ago
  • 2 points

Top mounting wasn't hard at all. As for the mousepad, I made it myself.

  • 20 months ago
  • 2 points

Thanks

[comment deleted by staff]
  • 20 months ago
  • 2 points

Sorry stupid autocorrect, I meant to say mouse pad

[comment deleted by staff]
  • 20 months ago
  • 1 point

gnarly build! link that siq wallpaper!

  • 20 months ago
  • 1 point

Google 'NZXT hypebeast wallpapers' you should be able to find it, maybe add csgo to those terms if you can't

  • 20 months ago
  • 1 point

Is that a cloth mousepad attached to a custom LED base?

  • 20 months ago
  • 1 point

Yup

  • 20 months ago
  • 1 point

Its super tight but very fit!

  • 20 months ago
  • 1 point

i have this case too how do you clean the front of it since its mesh

  • 20 months ago
  • 1 point

Love to see the top mounted rad in this case. Could you perhaps provide us with some thermals under high GPU & CPU load? Would like to see how hot the CPU gets pushing (or pulling can't tell) through the top there. Thanks for sharing! Awesome build +1!

  • 20 months ago
  • 1 point

Underload CPU and GPU top out at about mid-60s. The three front intakes really do an amazing job moving the hot air from the GPU and exhaust through the back and top along with the rad heat. So hot air is constantly being moved.

  • 20 months ago
  • 1 point

Awesome. Great execution on the air flow. Still trying to decide if I want to top or front mount my rad... Wondering how much the GPU temps would suffer. Thanks again for sharing.

  • 19 months ago
  • 1 point

what is that mouse pad

  • 19 months ago
  • 1 point

DIY

  • 19 months ago
  • 1 point

Were there any fitting issues with the top mounted radiator and the Trident Z RGB, I I wanted to do a similar setup but I read that the Meshify C with top mounted radiator leaves room for 40mm component height, Trident Z RGB is 44mm.

  • 19 months ago
  • 1 point

This has been on my mind also. Not only does this build NOT have that problem, it also looks like he had room to route the cables above the ram sticks and below the rad.

  • 19 months ago
  • 1 point

There's about 1.5cm gap between the fan/rad and the RAM, so no clearance issues on my part.

  • 19 months ago
  • 1 point

So your build looks fantastic, Its quite uncanny because the build I'm working on right now is strikingly similar considering I didn't see your build till after I finished putting my list together. I just have a question about your trident ram sticks, are you able to get stable 3200 with 1.35v on that strix mobo? I really want to get it but only if I can get it at that speed. Here is my build, let me know what you think? https://pcpartpicker.com/list/6HMD6X

  • 19 months ago
  • 2 points

Yeah, no problem ramping them up to 3200 from their 3000 out of the box speed.

  • 19 months ago
  • 1 point

I have this case, I'm sort of new to pc building, are there extension/splitter cables easily available for fans, or does your motherboard have 6 fan inputs already?

  • 19 months ago
  • 1 point

Setup Wars incoming?

  • 17 months ago
  • 1 point

Do Ram work at full speed 3200 mhz ?

  • 17 months ago
  • 1 point

Yeah, no hitches. I had to manually set them to 3200 however.

  • 15 months ago
  • 1 point

what is the model of this dell? nice build btw :>